93" Laser ARF kit Blue/Yellow Reflex scheme

Andrew Jesky AJ Aircraft 93” Laser 230z

Whether you're looking to go out and do some 3d huckin' or lay down a smooth-as-butter precision flight, the 93" Laser 230z is for you! The wings have been thoroughly refined to allow precision flying, while not sacrificing any 3d characteristics. With a generous fuselage height, the model flies as well on its side as it does upright. Generously sized control surfaces give you excellent authority at all speeds. The Laser 230z features an awesomely light but strong airframe and a light wing loading that will handle anything you want it to. 

Building the airplane is very straight forward. The rudder cables are pre-installed, hinges are pre-glued and sealed.  AJ Aircraft goes the extra step to make it easy to get this bird in the air in no time flat. Mounting options designed right into the airframe make it a snap to setup with pull-pull or push-pull rudder configurations. Stand-offs perfect for the DA-70, a gas fuel tank and even a bag of extra hardware are all included. High quality parts including dual G10 fiberglass control horns, carbon fiber wing tubes and heavy duty ball-links and turnbuckles ensure you won't need to spend more money replacing cheap hardware. 

This 30% airframe was designed around the DA-70 or equivalent, with lots of room for this beast of an engine without having to cut holes in the side of your cowl. Mounting templates are included for the DA-60/70 and 3W-50 to make engine installation as easy as can be. A full length pipe tunnel and 3 different pipe mounts gives you the ability to easily add pipes to tame your DB levels. Trust us when we say once you go full throttle with this baby, you won't want to slow down! As with its siblings, you'll see this is designed with next-gen building techniques to handle the punishment of todays 3D and extreme aerobatics with confidence. 

Prefer electrons over ignition? A Hacker Q-80 with 10-12s lipos will have the Laser screaming across the field. The crazy power and instant throttle response of the Q-80 makes the 93" Laser 230z a 3D/XA pop-toppin', tumblin', knife edge spinnin' insanity machine! Whichever you choose, we're sure it'll put a smile on your face every time you fly it!

Wing Span - 2360mm

Length - 2235mm

AUW (dry)- 9-10kg

Electric Power - Q-80

Gas Power - 60-70cc

Radio - 6 channel with 5 high torque servos

What's in the box:

Pre-hinged, glued and sealed ailerons & elevators

Carbon fiber main landing gear

Carbon fiber main wing tube

Removable horizontal stabs & rudder

G10 fiberglass control horns

Aluminum reinforced landing gear mount

Aluminum reinforced firewall

Aluminum standoffs for gas engines

Full-length canister tunnel

Canister muffler mounts

Heavy duty foam wheels with aluminum hubs

Heavy duty steel axles

Thick heavy duty pre-drilled wheel pants

Pre-drilled & rubber lined landing gear cuffs

Firewall drilling templates for common engines

Pre-run rudder pull-pull wires (turnbuckle also included for push-pull option)

High quality ball links & turnbuckles for all connections

Extra hardware bag for spares

Velcro for fuel tank or battery restraint

All airframe components covered in genuine Ultracote, available in 2 color schemes

Retro Scheme (True Red HANU866, White HANU870, Bright Yellow HANU872)

Patriot Scheme (True Red HANU866, White HANU870, Midnight Blue HANU885, Bright Yellow HANU872)

NOTE:  This product is shipped in two separate boxes.  

The main box measures 89"L x 18"W x 22"H (49 lbs. total),  The wing box measures 47"L x 29"W x 9"H (18 lbs. total).

We recommend the following equipment:

Hacker Q-80 motor

24x10 prop

Castle 160 ESC

2 x 6S LiPo batteries

Castle Pro BEC

Hitec D-954 servos

Secraft 1.75" Servo Arms x (4)

Secraft 3.5" Double Servo Arm

Also needed to complete:

(2) x 20cm extension for ailerons

(2) x 20cm extensions from the receiver to the aileron servos

(2) x 120cm extensions for the elevators

(1) x 30cm extension for the ESC to Receiver (if electric)

(1) x 30cm extension will be needed for the throttle servo and ignition (if gas)

(4) x 1,75" servo arms for elevators & ailerons

(1) x 3,5" servo arm for rudder

4" spinner