AMXFlight Yak-11 6S PNP (Red/White)

Description

Amewi - AMXFlight Yak-11 6S PNP (Red/White)

Ref. 24100

The Yak-11 was designed and entered service in the 1940s specifically for advanced flight training of fighter pilots. Its development was based on the experience of the Yak-1, -3, -7 and -9 single-seat fighter aircraft, which had already proven themselves in war, so that their best features could be incorporated into the Yak-11. The powerful, air-cooled radial engine with approx. 700 hp gave even better flight characteristics. The two-seat training aircraft was used by all member states of the Warsaw Pact as well as in the Middle East, Austria and China. The wingspan of this aircraft, which was mainly manufactured in Czechoslovakia, was 9.40 metres.

The AMXFlight YAK-11 is a very nice scale replica in red and white livery with all decals matching the original. The look and the quality of the model are outstanding - the plane convinces immediately by its size with a wingspan of 1450mm, the massive fuselage and the huge 16 x 6E propeller. The YAK-11 comes as a PNP version out of the box and all components such as servos, motor, controller, landing gear and flaps (spread flaps) are already installed. The assembly is limited only to screwing the tail unit and attaching the 2-piece main wing. All components are screwed. Only the scale antenna behind the cockpit has to be glued in. The voluminous fuselage is perfectly suitable for 6S LiPo batteries with a capacity of 5000mAh and the specified centre of gravity of the model is therefore easy to adjust. The canopy is very generously designed and allows clean working inside the fuselage. The landing gear has been designed with 5mm material thickness and active damping - it thus easily withstands the model's own weight as well as uneven take-off and landing areas. The spread flaps reduce the airspeed significantly to make landing as easy as possible.

The model is very docile to fly and appeals to advanced as well as experienced model pilots. With the recommended 6S LiPo 22,2V 5000mAh min. 30-40C long flight times of up to 10min are possible. The performance of the model is more than sufficient for e.g. dynamic aerobatics or fast, low overflights. The latter look particularly impressive due to the proportions of the model.

• High-quality, newly developed retractable undercarriage: in full metal with damping system and angled mount to dissipate the forces during take-off / landing in the best possible way.
• Highly efficient spread flaps as landing aid: During the landing approach, the speed is significantly reduced and the model can thus be controlled even better
• Very efficient brushless drive: With high efficiency for long flight time and extraordinary flying fun

Needed to complete:

• Radio/receiver (min. 6 channel)
• 6S 22.2V LiPo Battery 4500-5000mAh (XT-90 connector)
• Charger & lipo bag

Features

• Super optics (scale replica)
• Scale cockpit with pilot figure
• Very nice red/white paint
• Quick release for the canopy
• Wooden inlays for clean mounting of battery and receiver
• Very good flight characteristics at any speed (slow to fast)
• Very high quality material (EPO)
• Strong brushless motor (Potenza BL65 3D / 550KV)
• Large 80A regulator for 6S LiPo batteries
• Large 16 x 6 "E - propeller
• High quality digital servos with metal gears
• Fully steerable tailwheel for full control on the ground

• Wingspan: 1450mm
• Length: 1300mm
• Weight: approx. 2500g (without battery)
• Main material: EPO
• Thrust: over 1:1
• Motor: Potenza BL65 3D / 550KV
• ESC: 80A Hobbywing ESC brushless 6S with XT90 connector and BEC system for power supply
• Servos: 6x digital 19g MG
• Propeller: 16 x 6E High Performance Prop
• Electric retractable landing gear full metal spring loaded and with time delay on extension and retraction