Bel ons op +32 (0)50/858.020

Unisens-E, 140A, with XT60 connector

Unisens-E, 140A, with XT60 connector
SKU: GRAU33644
Only 1 left

€79.50

Stock: in stock

Product Description

Details

Description 
The Unisens E is a pure telemetry sensor especially for all electric models. It is so small and light but so powerful that it can be used in almost every model. 

The telemetry used must in Unisens E are specified only once in the settings. This is done either through our PC program ?? Unisens E Tool ??or with the UniDisplay. On delivery HoTT GAM is selected. 

To change the settings via PC or for firmware updates a suitable USB interface or an existing USB connection cable as of Jeti, multiplex or Graupner is necessary. See also the instructions. 

The Unisens E can measure the complete drive, ie voltage, current, capacitance and even the speed without additional sensors. A special attraction is in fact already a brushless speed sensor permanently installed. A small cable to connect to one of the three motor phases only has to be made ​​using the cable to measure the speed. 

As a barometric (atmospheric pressure) level sensor is integrated with high resolution, in addition to the altimeter, a Vario with Unisens E is realized . 

Similarly extensive alarms can be programmed to be reported via telemetry about individual stations. 

the Unisens e is available with various connection systems, so that, normally, nothing needs to be soldered. The current range extends symmetrically in both directions. This makes the pin assignment, so that the battery male or female has the positive terminal, not matter. The measurement direction is as simple simply set in the setup. 

Through our UniDisplay can all readings of Unisens E viewed directly live and all settings and alarms can be programmed. 

Whether gliders, aerobatic aircraft, helicopters, HLG or Slowflyer who Unisens E may due its low weight and compact size are used in almost every area. Of course, the Unisens E is suitable not only for model aircraft. It can also be incorporated into RC boats, RC cars, etc.. 

You buy the Unisens E a powerful in all respects universal RC telemetry sensor that exploits the possibilities of modern electronics to give you a little helper a great help in dealing with your RC models to be. 

possible update with S8344 and 7168.6.

characteristics
  • Complete measurement of electric drives with current, voltage, power, capacity, speed and altitude measurement
  • integrated brushless speed sensor
  • full telemetry support for Jeti Duplex (EX), Multiplex M-Link, Graupner HoTT, Robbe / Futaba FASSTest S.BUS2, JR DMSS and FrSky
  • Height measurement with automatic zeroing after switching
  • barometric Vario
  • Current measurement range up to 140 A in both directions, voltage up to 60 V (the maximum current carrying capacity of the connectors used but must not be exceeded!)
  • Connection for receiver signal for remote control of certain functions
  • direct connection to the GPS logger possible to record data in a file
  • Measuring the battery voltage receiver
  • Power supply through receiver
  • current status is indicated by LED
  • direct viewing of readings live and recorded with our UniDisplay
  • Parameter settings via PC, UniDisplay and telemetry possible
  • free firmware updates via a PC with existing USB connection cables as of Jeti, multiplex or Graupner possible
  • used due to its compact size and low weight almost anywhere

delivery
  • Unisens E with integrated height sensor / Vario
  • Receiver cable for telemetry / power supply
  • Connection cable for brushless speed measurement detailed colored user manual

Technical specifications
  • Current measurement range: 140 A in both directions, so - 140 A to 140 A +
  • Following loading periods are permissible:
  • - 100 A indefinitely
  • - 120 A for 1 minute
  • - 140 A for 20 seconds
  • Depending on the plug-in system but are the limits of the plug significantly lower!
  • Sensible values ​​are here:
  • - MPX green (double contact) and XT60 Duration: 50 A / 20s: 70 A
  • - 4 mm Gold plug Duration: 80 A / 20s: 100 A
  • - 5.5 mm gold plug length: 120 A / 20s: 150 A
  • Voltage measurement range: 0 to 60 V
  • Height measurement range: 0 to 8000 m NN, when switching is automatically reset
  • Receiver voltage measurement: 3.8 V to 10 V
  • Data rate: 10 Hz
  • Power supply: from receiver ?? supply via the telemetry connector link ?? (From 3.8 V up to 10 V)
  • Power consumption: 25 mA
  • External connections: 1 time connection for telemetry and power ( "Link")
  • 1 time phase connection for Brushless speed measurement
  • 1 times servo pulse input from the receiver
  • COM port for UniDisplay, GPS logger or PC
  • Dimensions: green MPX connector: 26 (38) x 29 x 9 mm
  • yellow XT60 connector: 26 (50) x 29 x 9 mm
  • 4 mm gold plug: 26 (55) x 22 x 9 mm
  • 5.5 mm gold plug: 26 (44) x 22 x 11 mm
  • 6 mm LMT gold plug: 26 (42) x 22 x 11 mm
  • Mass: 10 g - 14 g without cable (depending on the plug-in system), connection cable, 4 g

There are no products matching the selection.

Spare products

There are no products matching the selection.

Additional Information

Additional Information

SKU GRAU33644
Rating filter No
Brand Graupner
Cellnumber No
cilinder No
crate No
helisize No
multirotortype No
planetype No
spanwidth No
color No