Strega E full carbon orange/black

Seulement 1 en stock Envoyé sous 24h
959,00 € 792,56 €

Product Details

Description

RCRCM Strega E 2900mm Full carbon F3F Glider

Black/orange

 

We at Aerobertics are RCRCM dealer since 2010 and have flown many different models like the Sunbird, Typhoon, Strega, Tomcat, Tucan, … this makes it possible to give you the best advise.

Not sure which RCRCM model you should choose ? don’t hesitate to call or e-mail us !


The Strega makes for an excellent F3F sport model. If looking for something that's fast and can maintain energy on it's turns, then Strega is for you!! The elliptical planform supports a very large speed envelope, with no nasty habits at low speed. The wing is two part, with a carbon joiner and a removable V-Tail. The wings and fuse are ready for your plug and play multiplex setup, allowing for super fast setups at the field or slope. The fit and finish of the Strega is similar to much more expensive models, yet it still has an industry leading level of pre-assembly!

Supported by a large carbon wing joiner, the plug-in wings are of elliptical plan form which has been optimized to give a compromise between good lift distribution without the attendant tip stalling behavior sometimes seen in truly elliptical plan forms. Fin and tailplane sections are also of advanced symmetrical design and have no drag bucket at any speed. Glider for experienced pilots, Strega offers outstanding performance and excellent thermal flight qualities. It is also able to pick up speed, to convince you. It is able to fly in virtually all conditions and it is equipped with ailerons, flaps and a motor. All surfaces are pre-painted in the molds for flawless external finish. The whole model uses live hinges and wipers for control surfaces. From its super-efficient V-Tail, to its new larger diameter nose area, this little guy was built for fun!

 

Available in 4 Versions:

Fiberglass+Carbon Standard Version: Standard hollow molded fiberglass construction reinforced with carbon fiber which gives adequate stiffness and torsion stability with lower weigh and cost. Highly recommended for sport flying. 

Full Carbon Version: Wings built using full carbon cloth as well as fuselage reinforced with carbon from leading edge of the wing to the tail. This configuration gives the model enormous stiffness and torsion stability. 

The first two versions are available in stock. Besides, we have Light Carbon Version(less weight) and Double Carbon Version(with two layers of carbon), the last two versions are customized.


This is the full carbon version.


Paint Scheme is also available in a wide range of colors, besides standard color scheme presents on this website, also include some other color schemes. 

Another important thing is about the surface of airplane: RCRCM airplane is fully moulded, Mould precision ensures that each airplane has a complete aerodynamic layout. Yet in the process of composite airplane production, there seldom causes little tiny air bubbles, slight cloth grain, it shouldn’t be regard as a quality issue if it doesn’t affect flight.


About how to storage airplane in case you don’t fly it for a long time: It is better to keep airplane vertical hanging. Never give stress onto airplane surface, so as to avoid deformation.

 

Black/orange

 

We at Aerobertics are RCRCM dealer since 2010 and have flown many different models like the Sunbird, Typhoon, Strega, Tomcat, Tucan, … this makes it possible to give you the best advise.

Not sure which RCRCM model you should choose ? don’t hesitate to call or e-mail us !


The Strega makes for an excellent F3F sport model. If looking for something that's fast and can maintain energy on it's turns, then Strega is for you!! The elliptical planform supports a very large speed envelope, with no nasty habits at low speed. The wing is two part, with a carbon joiner and a removable V-Tail. The wings and fuse are ready for your plug and play multiplex setup, allowing for super fast setups at the field or slope. The fit and finish of the Strega is similar to much more expensive models, yet it still has an industry leading level of pre-assembly!

Supported by a large carbon wing joiner, the plug-in wings are of elliptical plan form which has been optimized to give a compromise between good lift distribution without the attendant tip stalling behavior sometimes seen in truly elliptical plan forms. Fin and tailplane sections are also of advanced symmetrical design and have no drag bucket at any speed. Glider for experienced pilots, Strega offers outstanding performance and excellent thermal flight qualities. It is also able to pick up speed, to convince you. It is able to fly in virtually all conditions and it is equipped with ailerons, flaps and a motor. All surfaces are pre-painted in the molds for flawless external finish. The whole model uses live hinges and wipers for control surfaces. From its super-efficient V-Tail, to its new larger diameter nose area, this little guy was built for fun!

 

Available in 4 Versions:

Fiberglass+Carbon Standard Version: Standard hollow molded fiberglass construction reinforced with carbon fiber which gives adequate stiffness and torsion stability with lower weigh and cost. Highly recommended for sport flying. 

Full Carbon Version: Wings built using full carbon cloth as well as fuselage reinforced with carbon from leading edge of the wing to the tail. This configuration gives the model enormous stiffness and torsion stability. 

The first two versions are available in stock. Besides, we have Light Carbon Version(less weight) and Double Carbon Version(with two layers of carbon), the last two versions are customized.


This is the full carbon version.


Paint Scheme is also available in a wide range of colors, besides standard color scheme presents on this website, also include some other color schemes. 

Another important thing is about the surface of airplane: RCRCM airplane is fully moulded, Mould precision ensures that each airplane has a complete aerodynamic layout. Yet in the process of composite airplane production, there seldom causes little tiny air bubbles, slight cloth grain, it shouldn’t be regard as a quality issue if it doesn’t affect flight.


About how to storage airplane in case you don’t fly it for a long time: It is better to keep airplane vertical hanging. Never give stress onto airplane surface, so as to avoid deformation.

 

Features

Special Features:

Control Surfaces: V-tail, Ailerons and Flaps

Two-piece hollow molded composite Full Carbon or Fiberglass wing design

Carbon Fiber reinforced wing with square wing joiner

Live hinges on the wing and rudder with pre-installed wipers

Smooth, gel-coated finish with pre-painted graphics

Fuselage hatch for V-tail servos

Glider fiberglass or full carbon with a beautiful finish comes with all necessary accessories for mounting

Includes:

2900mm Wingspan F3F Glider – Strega

Ballast Tub(for Motorless Glider only) , Motor mount(for electric version only), servo support, Push Rod, Clevis, Linkage Rod, Control horn, Servo Cover, Wing joiner, tail joiner, servo plate


Preferences                      motor

wingspan:                         2890mm

length:                              1450mm

Flying Weight:                   N/A

Empty Weight:                  Fiberglass+Carbon Standard Version:1610g
Full Carbon Version: 1720g

CG:center of Gravity       102-110 mm from leading edge

Tow hook setting              NO

Ailerons                            YES

Elevator                            YES

Rudder                             YES

Flaps                                 YES

Required Radio                 No less than 7 channels

Recommend equipment configuration for an electric version   basic configuration

Servos for wings               KST DS125MG*4

Servos for fuselage           KST DS215MG*2

Required Battery               4S 14.8V 2600mah 25c

Motor Mount Dia.             38mm

Propriétés

Plus d'infos
Manufacturer RC RCM
Référence d'article RCRCM009ORANGE
Envergure (mm) 2.900,00
Version du kit Almost ready to fly
Type d'avion Planeurs

Produits récommandées

In the box

2900mm Wingspan F3F Glider – Strega E FULL CARBON BLACK/ORANGE


Ballast Tube(for Motorless Glider only) , Motor mount(for electric version only), servo support, Push Rod, Clevis, Linkage Rod, Control horn, Servo Cover, Wing joiner, tail joiner, servo plate