Nous utilisons des cookies pour améliorer votre expérience utilisateur. Pour se conformer à la nouvelle directive concernant la vie privée, nous devons vous demander votre consentement pour définir des cookies. En savoir plus.
Unisens-E, 280A with 2x4mm cable
Product Details
Description
Unisens-E, 280A with 2x4mm cable
The small powerful RC telemetry sensor measures and
transmits voltage / current / power / capacity / energy / brushless speed /
altitude / vario
The UniSens-E is a pure telemetry sensor especially for all
electrical models. He is so small and light, but at the same time so powerful
that it can be used in almost any model.
In line with our philosophy of supporting as many systems as possible, the
UniSens-E also speaks the language of Jeti Duplex, Multiplex M-Link, Graupner
HoTT, Futaba, JR DMSS, FrSky and Spektrum (via spektrum adapters).
The used telemetry must be specified in the UniSens-E only once in the
settings. This happens either via our PC program "UniSens-E Tool" or
with the UniDisplay. When delivered, HoTT GAM is selected.
Without additional sensors, the UniSens-E can measure the
complete drive, ie voltage, current, capacity and even the motorspeed. As a
special feature, a brushless speed sensor is already installed. To measure the
speed, only a small cable connection to one of the three motor phases has to be
made with the enclosed cable.
Since a barometric (air pressure) height sensor with high resolution is integrated,
a Vario is realized in addition to the height measurement.
Likewise, extensive alarms can be programmed, which are reported via telemetry
on your transmitter.
The UniSens-E is available with different plug-in systems so that normally
nothing has to be soldered. The current measuring range extends symmetrically
in both directions. Thus, the pin assignment plays, so whether the battery
males or females at the positive pole, no matter. The measuring direction is
simply set in the setup.
All measured values of the UniSens-E can be viewed directly live via our
UniDisplay and all settings and alarms can be programmed.
Glider, aerobatic plane, helicopter, HLG or slowflyer, the UniSens-E can be
used in almost every area due to its low weight and compact size. Of course,
the UniSens-E is not only suitable for aircraft models. It can also be
installed in RC boats, RC cars, etc.
With the UniSens-E you get a universally powerful universal RC telemetry
sensor, which uses the possibilities of modern electronics to help you as a
small helper with the handling of your RC models.
Complete measurement of electric drives with current,
voltage, power, capacity, speed and height/vario.
Integrated brushless speed sensor
Full telemetry support for Jeti Duplex, Multiplex M-Link,
Graupner HoTT, Futaba, JR DMSS, FrSky and Spektrum (via Spektrum Adapter)
Height measurement with automatic zeroing after switching on
barometric vario
Current measuring range up to 140 A in both directions,
voltage up to 60 V.
(The maximum current carrying capacity of the plug used must not be exceeded!)
reinforced version with 280 A current measuring range
available
Connection for receiver signal for remote control of certain
functions
direct connection to the GPS-Logger possible for data
recording in a file
Measurement of the receiver battery voltage
Power supply by receiver
current status is signaled via LED
Direct viewing of the measured values live with our
UniDisplay
Parameter settings via PC, UniDisplay and telemetry possible
PC Software for Settings and Updates (SM UniSens-E Tool)
compact size and low weight
Features
- Complete measurement of electric drives with current, voltage, power, capacity, speed and height/vario.
- Integrated brushless speed sensor
- Full telemetry support for Jeti Duplex, Multiplex M-Link, Graupner HoTT, Futaba, JR DMSS, FrSky and Spektrum (via Spektrum Adapter)
- Height measurement with automatic zeroing after switching on barometric vario
- Current measuring range up to 140 A in both directions, voltage up to 60 V. (The maximum current carrying capacity of the plug used must not be exceeded!)
- Connection for receiver signal for remote control of certain functions direct connection to the GPS Logger possible for data recording in a file
- Measurement of the receiver battery voltage
- Power supply by receiver current status is signaled via LED
- Direct viewing of the measured values live with our UniDisplay
- Parameter settings via PC, UniDisplay and telemetry possible
- PC Software for Settings and Updates (SM UniSens-E Tool)
- Compact size and low weight
- Voltage measuring range: 0 to 60 V
- Height measurement range: 0 to 8000 m above sea level, zeroing takes place automatically when switched on
- Receiver voltage measurement: 3.8 V to 10 V
- Data rate: 10 Hz
- Power supply: from receiver supply via the telemetry connection "Link" (from 3.8 V to a maximum of 10 V)
- Power consumption: approx. 25 mA
- External connections: 1 connection for telemetry and power supply ("Link")
- 1 x phase connection for brushless speed measurement
- 1 servo pulse input from the receiver
- COM connection for UniDisplay, GPS logger or PC
- Dimensions : 55 x 22 x 9 mm
- Weight : 17g - 30g (depending on the plug system)
Propriétés
Manufacturer | Unisens |
---|---|
Référence d'article | US3115 |